PLC FX1N-24MT-ES/UL Manual MITSUBISHI FX1N-24MT-ES/UL HARDWARE MANUAL

Input points: 32 points.
Power supply: the basic unit to the expansion module to provide power.
Terminal type: connector type.
Weight: 0.2kg.
FX3GC, FX3UC can be directly connected to the input and output expansion equipment, to achieve a compact expansion.
Can choose 16 points, 32 points of the relay or transistor input and output models FX1N-24MT-ES/UL Manual.
FX2NC-16E_-T-DS for terminal units can be disassembled models FX1N-24MT-ES/UL Display: 7 segment digital display + icon display.
Can monitor, change the value of software components.
Can also be simple to operate, change the value.
Equipped with a button operation can be used (operator certification function) and control through the PLC control function,
Can be used with the function expansion board FX1N-24MT-ES/UL Manual.
Can be installed directly to the FX3S, FX3SA, no wiring. Memory format: flash memory.
Number of steps: up to 16000 steps.
Battery support: do not.
Write, delete method: installed on the PLC through the peripheral devices to write, delete. Max input / output points: 10 points.
Power supply voltage: 24VDC.
Input points: 6 points.
Output points: 4 points.
Output type: Transistor (source) FX1N-24MT-ES/UL Manual.
Power consumption (W): 6.
Weight (kg):0.22.
Size (WxHxD) mm:60x90x49.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator MITSUBISHI FX1N-24MT-ES/UL HARDWARE MANUAL.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0 MITSUBISHI FX1N-24MT-ES/UL HARDWARE MANUAL.
FX1S provides up to 30 I/O points, and can be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment MITSUBISHI FX1N-24MT-ES/UL HARDWARE MANUAL. Max input / output points: 48 points.
Supply voltage: 100 - 240VAC.
Input points: 24 points.
Output points: 24 points.
Output type: silicon controlled.
Power consumption: 50VA.
Weight (kg):0.85.
Size (WxHxD) mm:182x90x87.
Since the FX2n series have the following features: the maximum range of inclusive of the standard features, program execution faster, the full complement of communication function, suitable for different countries in the world, and the power to meet a large number of special function modules of individual needs,
It can provide maximum flexibility and control capability for your factory automation applications.
Control 16~256 point.
Built in 8K capacity of the RAM memory, the maximum can be extended to 16K.
CPU arithmetic processing speed of 0.08 S/ basic instructions.
On the right side of the FX2N series can be connected to the input and output expansion modules and special function modules.
The basic unit is built in the 2 axis independent maximum 20kHz positioning function (transistor output type).
Quick disconnect the terminal block, which adopts excellent maintainability to quickly disconnect the terminal blocks, even if the cable is then replaced by the cable.
Developed a range of special function modules to meet the needs of ddifferent - analog I/O, high speed counter FX1N-24MT-ES/UL .
Positioning control to achieve the 16 axis, the pulse train output or for the J and K type thermocouple or Pt sensor developed the temperature module.
A total of 8 special function mmodules can be configured for each FX2n main unit FX1N-24MT-ES/UL Manual.
Note recording function, Component annotation can be recorded in the program register.
Online program