Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMPS type motor
>> YASKAWA SGMPS-15ACA2SE Rated output: 400W (04KW) Medium inertia flat type motor SGMPS-15ACA2SE
YASKAWA SGMPS-15ACA2SE Rated output: 400W (04KW) Medium inertia flat type motor SGMPS-15ACA2SE
Brand:
Yaskawa
Name: Medium inertia flat type motor
Model: SGMPS-15ACA2SE
Sigma -V series servo motor SGMPS.
Rated output: 1.5kw.
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP55 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Name: Medium inertia flat type motor
Model: SGMPS-15ACA2SE
Sigma -V series servo motor SGMPS.
Rated output: 1.5kw.
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP55 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
High performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: paint.
Function: pressure feedback control function YASKAWA SGMPS-15ACA2SE.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models SGMPS-15ACA2SE
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device YASKAWA SGMPS-15ACA2SE.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller YASKAWA SGMPS-15ACA2SE. Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: analog voltage, pulse sequence type (rotary servo motor) YASKAWA Medium inertia flat type motor.
Optional (hardware): rack mounting type.
With the latest technology to pursue the use of convenience YASKAWA Medium inertia flat type motor.
The use of new non adjustment function, no need to adjust.
The vibration suppression function is also strengthened, and the load fluctuation can be effectively suppressed.
Greatly shorten the setting time.
Using engineering tool SigmaWin+ to set the guide function and the distribution confirmation function,
Can look at the picture simply to complete the start YASKAWA Medium inertia flat type motor.
Achieve a high response 1kHz above.
Equipped with a new advanced automatic tuning function.
Through the model tracking control, the positioning time is shortened,
And through the vibration suppression function, easy to achieve a smooth mechanical control.Servo motor SGMDH type.
Rated speed: 3000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with D90V brake.
Partial flat series: the need to install the servo motor in a small space.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contaact, can also be completed in a short time the best set SGMPS-15ACA2SE.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regeneerative resistance connection terminals YASKAWA SGMPS-15ACA2SE.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistor
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: paint.
Function: pressure feedback control function YASKAWA SGMPS-15ACA2SE.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models SGMPS-15ACA2SE
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device YASKAWA SGMPS-15ACA2SE.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller YASKAWA SGMPS-15ACA2SE. Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: analog voltage, pulse sequence type (rotary servo motor) YASKAWA Medium inertia flat type motor.
Optional (hardware): rack mounting type.
With the latest technology to pursue the use of convenience YASKAWA Medium inertia flat type motor.
The use of new non adjustment function, no need to adjust.
The vibration suppression function is also strengthened, and the load fluctuation can be effectively suppressed.
Greatly shorten the setting time.
Using engineering tool SigmaWin+ to set the guide function and the distribution confirmation function,
Can look at the picture simply to complete the start YASKAWA Medium inertia flat type motor.
Achieve a high response 1kHz above.
Equipped with a new advanced automatic tuning function.
Through the model tracking control, the positioning time is shortened,
And through the vibration suppression function, easy to achieve a smooth mechanical control.Servo motor SGMDH type.
Rated speed: 3000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with D90V brake.
Partial flat series: the need to install the servo motor in a small space.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contaact, can also be completed in a short time the best set SGMPS-15ACA2SE.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regeneerative resistance connection terminals YASKAWA SGMPS-15ACA2SE.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistor
...More relevant models >>>>
Last one: Yaskawa Medium inertia flat type motor SGMPS-08ACA2SE
next one: Yaskawa Medium inertia flat type motor SGMPS-01ACA61E
Related download