LK Automation Limited
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGDV-____21 Type (used by rotary type servo motor) >> SGDV-R70F21A YASKAWA SGDV-R70F21A Servo driver MECHATROLINK- III communication command type

SGDV-R70F21A YASKAWA SGDV-R70F21A Servo driver MECHATROLINK- III communication command type

Brand: Yaskawa
Name: Servo driver MECHATROLINK- III communication command type
Model: SGDV-R70F21A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.05kw.
Power supply voltage: single phase AC100V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.

Low inertia, high speed servo motor type SGM7A (rated speed 3000r\/min).
Rated output: 5.0kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with hold brake (DC24V).
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 million 770 thousand \/rev pulse) YASKAWA SGDV-R70F21A.
The maximum torque of 350% (small capacity) SGDV-R70F21A
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
It is helpful to the servo performance of ultra high speed and ultra precision control. most
To limit the performance of the device to solve the problemSigma -V series servo motor SGMGV YASKAWA SGDV-R70F21A.
Rated output: 15kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC90V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake) YASKAWA SGDV-R70F21A.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type YASKAWA Servo driver MECHATROLINK- III communication command type.
Installation method: flange type.
Heat resistance grade: F YASKAWA Servo driver MECHATROLINK- III communication command type.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type YASKAWA Servo driver MECHATROLINK- III communication command type.
Rated speed: 1500r\/min.
Power: 11Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuitt,
Alarm can only turn off the main circuit power supply, easy to maintain SGDV-R70F21A.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 YASKAWA SGDV-R70F21A.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control


...More relevant models >>>>