LK Automation Limited
Home >> Products >> MITSUBISHI >> Q series PLC >> Positioning module >> Corresponding SSCNET III positioning module >> QD74MH16 Corresponding III SSCNET positioning module Control unit: pulse MITSUBISHI QD74MH16

QD74MH16 Corresponding III SSCNET positioning module Control unit: pulse MITSUBISHI QD74MH16

Brand: MITSUBISHI
Name: Corresponding III SSCNET positioning module
Model: QD74MH16
16 axes.
Connect SSCNET III.
Control unit: pulse.
Location data: 32 data / axis.
Ideal solution for simple multi axis positioning.
A variety of functions, such as positioning control, constant velocity control, and other positioning control systems.
The multi axis system is most suitable for simple positioning control.
Ideal selection for high speed linear positioning control in multi axis system.
Linear interpolation operation with up to 4 axes can be carried out.
With the electronic gear, gap compensation, absolute position system, such as basic positioning function.

Adapter for mounting DIN guide rail.
For Q32SB, Q33SB, Q35SB, Q33B, Q52B, Q55B, Q63B.Battery replacement.
Initial voltage 3.0V.
Replace large capacity battery module with cable.
Current capacity: 18000mAh.
Service life: 5 years.
Outline dimension: 98*55.2*87mmOutput: 6 channels.
Input (resolution): 0~4000; -4000~4000; 0~12000; -12000~12000; -16000~16000 MITSUBISHI QD74MH16.
Output: DC-12V~12V; 0~22mA QD74MH16
Conversion speed: 6ms/ channel.
40 pin connector.
Isolation between channels.
The possibility of expanding control with intelligent function.
At the same time, the channel isolation analog module realizes high isolation voltage,
Further improve the accuracy of the benchmark.
Provide support for process control using a general purpose programmable controller MITSUBISHI QD74MH16.
Flow meter, pressure meter, other sensors can be directly connected to analog input,
Control valve can also be directly connected to analog output.
Hardware and installation costs have been greatly reduced due to the need for an external isolation amplifier.
High insulation strength.
Can isolate electrical interference, such as current and noise, etc MITSUBISHI QD74MH16. .
Standard analog input module.
Isolated analog input module.
No external isolation amplifier required.
Without the use of inter channel isolation analog modules.
Using the inter channel isolation analog module. For A6TBXE/A6TBY36E/A6TBX54E/A6TBY54E/A6TBX70E (common cathode; source) long 0.5m.Input: 2 channels.
50kpps MITSUBISHI Corresponding III SSCNET positioning module.
Counter input signal: DC5/12/24V.
External input: DC5/12/24V.
Uniform output: Transistor (drain type) MITSUBISHI Corresponding III SSCNET positioning module.
Used to replace the A series of large modules "AD61".
40 pin connector.
Support high resolution devices. Pulse input and high speed counter module product group satisfying high speed and high precision control application.
High speed counter module for counting high-speed pulse train.
Can be used in combination with the external encoder for positioning and other control MITSUBISHI Corresponding III SSCNET positioning module.
The maximum count rate can be switched, and the low frequency pulse is counted from the high speed pulse to the rising edge / falling edge.
Each 1 channel is equipped with 2 points of external uniform output.
Can be selected according to the use of "consistent output function", "continuous comparison function", to achieve high-speed control of external equipment. (QD64D2)
Provides a variety of functions, such as the same output test function (using a continuous comparison function), the default function, the latch counter fuunction,
In order to meet the needs of various applications QD74MH16. (QD64D2)
The maximum count rate of the input pulse can be up to 8Mpps (differential input, 2 phase, 4 double frequency).
Can be in the semiconductor, liquid crystal mannufacturing and other high position accuracy requirements of the equipment,
Perform accurate position tracking using high resolution encoders MITSUBISHI QD74MH16. (QD65PD2)


...More relevant models >>>>