LK Automation Limited
Home >> Products >> MITSUBISHI >> Servo driver/Servo motor >> MR-E series >> HF-SN302BJ-S100 MITSUBISHI HF-SN302BJ-S100 Servo motor without oil seal

HF-SN302BJ-S100 MITSUBISHI HF-SN302BJ-S100 Servo motor without oil seal

Brand: MITSUBISHI
Name: General motors for MR-JE and MR-E
Model: HF-SN302BJ-S100
Type: HF-SN servo motor, medium inertia power.
Rated output power: 3.0kw.
Rated speed: 2000r/min.
Electromagnetic brake: there.
Oil seal: have.
Encoder resolution: 131072p/r.
S100 representative: Super MR-E special motor.
KH003 special mark for Super MR-E.
High performance and easy to operate, reduce work load.
Enhanced system cost performance.
High performance, high precision positioning (servo motor encoder resolution: 131072).
High response.
Suppression of vibration by adaptive vibration suppression control.
Using personal computer and servo setup software to optimize tuning.
Has 2 types of interfaces:
Position control and speed control with pulse train interface.
The analog input interface is used for speed control and torque control.
Wide use.
Machining equipment and machine tool feed.
Used for food, packaging equipment and feeding device.
For textile machinery, etc..
Can improve the performance of equipment.
Servo amplifier terminals are used to reduce the required wiring time.
The connector is located in front of the servo amplifier, which is convenient for cable connection.
The gain adjustment can be easily carried out by the real-time automatic tuning function.

"MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 3.5kw.
Built in positioning function.
Voltage: 3 phase AC200VAC or single phase AC230V.
Compatible with "MR-J2S- CP-S084" - servo amplifier and interface unit "MR-J2S-TO1" positioning by CC-Link
Simply setting the point table MITSUBISHI HF-SN302BJ-S100.
AC servo can be used as the driving source of the field network HF-SN302BJ-S100
Using servo amplifier built-in positioning function, position data and speed data, you can set the CC-Link.
Start, stop and display can also be transmitted through the CC-Link.
Serial communication reduces wiring.
AC servo distributed control system can be easily constructed. "Motor series: ultra low inertia, small capacity MITSUBISHI HF-SN302BJ-S100.
Using a serial absolute / incremental encoder.
Rated output power: 0.4kw.
Rated speed: 3000rpm.
With the brake with brake.
Without GB.
Shaft end: straight shaft.
The rotor of the servo motor is a permanent magnet, and the control of the servo amplifier is controlled by the U/V/W three-phase electric electromagnetic field,
The rotor rotates under the action of the magnetic field, and the encoder feedback signal of the motor is given to the driver,
According to the feedback value and the target value, the driver is compared,
Adjust the rotor rotation angle MITSUBISHI HF-SN302BJ-S100.
The accuracy of the servo motor is determined by the resolution of the encoder. Type: MR-J series MITSUBISHI Servo motor without oil seal.
Rated output: 0.1KW.
Applicable motor series: HA-FF, HA-SE.
Voltage: single phase AC100V.
It is very helpful to improve the stability of the low speed control of the servo motor MITSUBISHI Servo motor without oil seal.
But there is no direct effect to improve the accuracy of position control.
There are, of course, software compensation that is similar to pitch compensation,
Can improve the physical resolution of the single lap, so as to improve the accuracy of positioning control MITSUBISHI Servo motor without oil seal.
This can be effectively used in the use of the robot control oof the indexing table HF-SN302BJ-S100.
It is also because of the application of splicing technology,
The rotary encoder will be more widely used in the high precision servo control in the harsh environment.
The use of rotary encoder with 224/ in the servo motor has been used in the servo motor MITSUBISHI HF-SN302BJ-S100.
Encoder serial communication system, the communication frequency can only be limited to 10M.


...More relevant models >>>>