MITSUBISHI GT2508-VTWA-GF Manual GT2508-VTWA-GF Non-Mitsubishi Products 1 Connection Manual

A series of high performance models that are widely used in network or single machine work environments.
Screen size: 10.4 inches.
Display color: 256 color or more color.
Mounting type: panel mounting type.
Resolution: SVGA (800 x 600).
Display device: TFT color (high brightness, wide viewing angle) GT2508-VTWA-GF Connection Manual.
Host frame color: black.
Power type: DC24V.
Communication interface: with built-in RS-422 GT2508-VTWA-GF
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system GT2508-VTWA-GF Connection Manual.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly GT2508-VTWA-GF Connection Manual. Cable length: 5.0m.
For QnA/ACPU/ motion controller CPU (A series, extended basis system) and the connection between GOT.
Applicable models: GT16, GT15, GT11. Cable length: 20m.
The connection between the FXCPU (MINI-DIN8 pin connector) and the graphic operation terminal.
Connection between FXCPU communication function extension board (MINI-DIN8 pin connector) and GOT.
Applicable models: GT10, GT21. Protective film for 10.4 inch screen.
Transparent (frame: white), 5.
Applicable model: GT16. Features: high cost of second models.
Picture size: 10.4 inches.
Resolution: VGA.
Display: TFT color.
Panel color: black.
Power type: AC100~240V.
Specification rich, design at ease
GT23 standard supports SD memory card and standard equipped with Ethernet, RS-232, RS-422/485, host/device USB interface.
Support log, one to many connections, FA transparent transmission and other diverse FA machine related functions.
System configuration diagram shows in order to form the connection with the GOT programmable controller system,
Easily confirm module status. In addition, after touching each module,
Can start its corresponding expansion function, to facilitate system maintenance, shorten the time of failure.
1, simple design
In order to cope with the use of a variety of scenarios, to abandon all the nonsense of the decoration, the use of straight tone of the minimalist design.
2, plane body
Surface mining pure plane design, easy to clean. (USB interface at the back)
3, Ethernet interface
Up to 2 different manufacturers can be connected to the FA machine.
4, RS-232 interface
Can connect all kinds of FA machine, bar code reader, serial printer.
5, RS-422/485 interface
Can be connected to a variety of FA machines, bar code reader.
6, USB interface: device USB (Mini-B USB)
Can connect to the computer to transfer data.
7, USB interface: host USB (USB-A)
USB data can be transmitted through the USB memory or read log data, such as the GOT data, but also can be connected to tthe use of the mouse, keyboard GT2508-VTWA-GF Manual .
8, SD memory card slot
Can save alarm and log data, such as a large number of data.
Can be collected through the GOT programmable controller, temperature regulator and other data, and to chart, list display GT2508-VTWA-GF Manual .
Computer analysis can also be used to save the data. Even in the case of a power outage, the log data can be saved to the built-in SRAM.